鋼波紋涵管路堤法的工藝流程為：施工前準備—施工放樣—設置圍堰—排水清淤—平整場地—檢測壓實度、含水量等—水準測量—平整場地—基礎分層回填—檢測壓實度含水量等—水準測量—平整場地—施工方樣—拼裝管節—檢測密水情況及管底縱坡—檢測并補救防腐涂層—涵管就位——兩側分層回填—檢測壓實度、含水量等—進出口處理。

鋼波紋涵管在2019年的工作重點在哪里？

涵洞施工前應根據具體情況修筑相應長度的施工便道，并合理組織過往車輛。涵洞施工前必須對到現場的涵管節及其附屬配件進行檢測，一方面檢測其結構尺寸是否滿足要求，另一方面檢測其表面防腐是否達到要求；必要時須在鍍鋅涂層表面在增涂瀝青或其他防腐材料。

拼接波紋管涵怎樣施工？

鋼波紋涵管反開槽回填法涵洞施工前備齊所需材料。涵洞施工前應準備涵洞施工過程中試驗。檢測儀器和設備，落實試驗人員。金屬波紋涵管路堤法涵洞施工前施工單位需要通知監理及相關人員到場，并按程序辦理施工前的手續。

涵管施工前應設一名管道安裝指揮人員，負責指揮吊裝及施工人員的現場操作；設置1~2名技術人員負責放線。涵管安置等控制關鍵技術；同時配置適當的輔助人員。涵洞施工前應備齊所需的機械設備及相關工具，反開槽回填法的工藝流程為。

鋼波紋涵管洞施工工藝流程可分為路堤法和反開槽回填法，由于后者涵洞的施工多在路基施工結束后和改建涵洞，所以不影響路基施工整體進度，一般后者較為多見。盡管在外力上二者存在一定的差異，但施工工藝相差不大。下面分別予以敘述。

鐵路鋼波紋涵管

施工前準備—施工放樣—開挖涵管及施工現場—平整場地—檢測壓實度—含水量等—水準測量—基礎分層回填—檢測壓實度、含水量等—水準測量—平整場地—施工放樣—拼裝管節—檢測密水情況及管底縱坡—檢測并補防腐涂層—涵管就位—兩側分層回填—檢測壓實度、含水量等—管頂分層回填——檢測壓實度、含水量等—進出口處理。（hanihanbj.com）