鋼波紋管先從軸向用M4螺釘固定在定位環上，再用m螺釘從直徑方向將定位環固定在軸套上，這樣就存在累計誤差，不易確保鋼波紋管端面垂直于軸套。壓蓋上沖刷油和冷卻水注入孔位置不合理，冷卻水的通徑有一半孔被靜環密封圈擋住。

The steel bellows is fixed on the locating ring with M4 screw from the axial direction, and then the locating ring is fixed on the shaft sleeve with m screw from the diameter direction, so there is accumulated error, and it is not easy to ensure that the end face of the steel bellows is perpendicular to the shaft sleeve. The location of flushing oil and cooling water injection hole on the gland is unreasonable, and half of the cooling water diameter hole is blocked by the static ring seal ring.

鋼波紋管

形成靜環冷卻水減少，密封面冷卻效果不好;沖刷油孔離動、靜環密封面太遠(軸向間隔太長)，使沖刷油不易注入到鋼波紋管密封處。直徑偏小鋼波紋管內徑62mm，密封比壓偏大;軸徑為55mm，軸套外徑為60mm，壁厚僅為2.5mm，壁厚偏小，簡單變形，形成拆、裝困難。

用戶柜子中心的孔的直徑≥2.5cm，由于金屬管兩側的接頭比中心軟管厚，而且用戶柜子的一些眼睛僅夠假如裝置要求用戶事前打孔或重新打孔以方便波紋管穿過則軟管要經過。一些用戶原來的天然氣界面十分接近大理石臺面。

鋼波紋管

金屬管界面需要具有程度的曲率，較小曲折面積≥30mm。假如曲率小于上述大小，則無法暫時裝置。該界面位于用戶家的一角，而且被單獨阻止。存在潛在的安全隱患，需要在裝置前進行糾正。請檢查接頭是否別離卡住以及是否能夠運用扳手(扳手長度為20cm)。

鋪裝于壩基下的金屬波紋管的管身要設定預埋拱度，其尺寸革命老區基土很有或許出現的下移量，涵底橫坡和回填土高寬比等要素綜合性考慮到，一般能為長度的百分之零點六到百分，不適合超越百分之二，以確保管路中心不出現凹現或山體滑坡。//hanihanbj.com/