鋼波紋管方位定位要準確，尤其是接近接頭的部位，波紋管涵定位鋼筋距離為0.5米，不得短少。焊接鋼筋接近波紋管涵時，要采用方法保護波紋管不得被灼傷，如不留神灼傷，灼傷處要用膠帶包裹緊密。考慮到頂板波紋管涵數量在逐漸削減，但凡與波紋管涵抵觸的部件都要逃避波紋管。

鋼波紋管

澆筑砼時，制止對著波紋管涵放料。振搗棒制止與波紋管碰撞，制止兩個振搗棒夾著一根波紋管涵振搗。特別是腹板振搗時，制止振搗棒在同一方位長期振搗，振搗時刻以不逾越20秒為準。鋼波紋管接頭的方法：波紋管涵接頭處要外包0.3米長的大號波紋管。

When pouring concrete, it is forbidden to discharge materials to corrugated pipe culvert. The vibrator shall not collide with the corrugated pipe, and the vibration of two vibrators with one corrugated pipe culvert shall be prevented. Especially when the web is vibrated, the long-term vibration of the vibrator in the same direction shall be prevented, and the vibration time shall not exceed 20 seconds. Method of steel bellows joint: the joint of bellows culvert shall be wrapped with 0.3m long large bellows.

并且兩端頭要對半擰緊，中心不得留有空位。為保證中心不留空位，應在兩接頭端頭處做好符號。做好后要用膠帶包裹緊密，以防漏漿。從一側裝置管節開始，試管節中心線和根底縱向軸線平行，適當調節兩管節相鄰法蘭間距離在2cm左右后，悉數穿上螺栓，擰上螺絲，帶平扣即可。

鋼波紋管

以此方式逐節依次裝置銜接，準確放樣管節軸線位置，合理安排每節管的位置。波紋管涵管壁表里涂刷瀝青，涂層厚度要到達1mm以上。用千斤頂校對整個涵管的軸線，使其處于中心軸線上。鋼波紋管，是指鋪埋在公路、鐵路路下的涵洞用的螺紋波紋管。

它是由波形鋼板卷制成或用波形鋼片組拼成的圓形鋼結構管。它的波紋結構可使涵洞路面受力合理，荷載分布均勻，并具有必定的抗變形能力，能處理北方冰冷區域（霜凍）對橋梁和管涵砼結構的損壞問題。

使路外表沒有伸縮縫，進步行車穩定性；有利于改進軟土地基結構與路堤交界處的“錯臺”現象。當管節悉數銜接結束后，在相鄰法蘭間鑲石棉墊，石棉墊鑲牢后，再以人工對稱鎖緊螺絲，直至外觀調查兩法蘭間隙在2～3mm即可。//hanihanbj.com/