為保證鋼波紋管的距離和順直，可用鋼筋支架對波紋管進行點焊固定，防止澆筑砼時左右位移。管道鋪設后，出于其它原因造成管壁呈現局部損壞，當損壞程度比較小時，可經過焊槍修補處理，如環向、縱向裂縫小于管周長的112或孔徑60mm的情況。

鋼波紋管

當損壞程度大于這些數據時，宜經過換波紋管或基建筑檢查井、連接井等修補方法處理。雨期時節應留意防止管材漂浮、位移等現象，當管道裝置完畢沒有覆土遇到水泡情況時，應復測管底與管中心高程，并做好返工處理辦法。

鋼波紋管安置和線盒及預留洞處相協調，管線盒盡可能安置在管間肋的位置。波紋管運工作面后，鋪放前應檢查管材的外形及管端的堵頭封堵是否嚴密，對變形或裂口處進行修補。并對波紋管的外形和標準進行檢查，按標準、型號分類平臥疊層堆放。

The placement of steel bellows shall be coordinated with wire box and reserved hole, and the wire box shall be placed at the position of ribs between pipes as far as possible. After the corrugated pipe is transported to the working face, the shape of the pipe and the sealing of the plug at the pipe end should be checked before laying, and the deformation or crack should be repaired. Check the shape and standard of the bellows, and stack them horizontally according to the standard and model.

鋼波紋管

依據放線位置進行波紋管的鋪設裝置，在裝置過程中，應在管頂襯托木板作維護，不得直接踐踏波紋管。因波紋管底部砼層較薄，在裝置底部鋼筋時，有必要安放并固定好墊塊或馬(ma)凳筋，以保證底部砼層的厚度。

一般將管拉結錨固在板底層鋼筋上，依據管徑巨細，每0.8-1.0米管長錨固一次鐵絲，底筋的錨固可別離放兩條通長鋼筋做壓筋，然后用鐵絲將鋼筋與模板支架拉結錨緊。壓筋和拉結鐵絲的巨細、拉結錨固距離經核算后確認或由設計院給定。

在管材放入溝槽時，應依據施工設備、溝槽以及管徑巨細，且鄙人管過程中應留意不得與溝壁、溝底呈現劇烈磕碰現象，宜經過適宜的吊車等機械平穩下溝，一起吊裝時不得呈現穿心吊，應少有兩個支撐吊點。為防止澆筑砼時波紋管上浮，將波紋管拉結錨固。//hanihanbj.com/