鋼波紋管是一種柔性結構，鋼波紋管在結構上具有橫向補償位移的特性，可以充分發揮鋼材抗拉功能強、抗變形才干的特點，具有較大的抗變形才干和抗沉降才干，特別適合于軟土、脹大土、濕陷性黃土等地基承載力較低的區域和地震多發區域。

鋼波紋管與鋼波紋涵管有什么區別？用途一樣嗎？

由于金屬鋼波紋管施工簡略且施工工期短（一般一道涵洞的施工時刻大約在10天-15天左右）縮短了多年凍土的暴露時刻，凍融量小，故特別適用于多年凍土區域。金屬鋼波紋管施工時對周圍環境的損壞小，適用于生態環境軟弱的區域。

鋼波紋管

該產品施工中只需要對基礎進行砂礫回填處理，對進出口進行混凝土或砌石施工處理，對砂、石材、鋼筋等用量小，非常實用于砂石缺少的區域。該產品選用規范化規劃、工廠加工出產，出產不受環境影響，進行會集工廠化出產，出產周期短，實用于質量要求高，工期緊，基礎差的工程項目。

鋼波紋管與鋼波紋涵管有什么區別？用途一樣嗎？

小孔徑波紋管為圓形整體管，選用整管節拼裝、法蘭螺栓聯接；大孔徑波紋管為分片拼裝。為便利運送與施工，在滿足鋼波紋管受力功能及規范運用要求的前提下，波紋管也可運用兩片半圓式拼裝施工。焊接外表不應有氣孔、裂紋、夾渣及飛濺物等缺點。

鋼波紋管

澆筑砼時，不能對著波紋管放料。振搗棒不能與波紋管磕碰，制止兩個振搗棒夾著一根波紋管振搗。特別是腹板振搗時，制止振搗棒在同一方位長時刻振搗，振搗時刻以不逾越20秒為準。為確保在多年凍土區域鋼波紋管洞在較大凍脹量下的變形和應力要求，選用小壁厚為3mm的鋼波紋管。

當鋼波紋管洞換填厚度越大、壁厚越厚時，凍脹量對結構的影響越小。焊接鋼筋接近波紋管時，要采取辦法保護波紋管不能被灼傷，假設不小心被灼傷到，灼傷處要用膠帶包裹緊密。考慮到頂板波紋管數量在逐漸減少，但凡與波紋管沖突的部件都要逃避波紋管。//hanihanbj.com/