鋼波紋涵管超長的運用壽命:鋼鋼波紋涵管是選用鋼板熱浸鍍鋅，所以運用壽命長，壽命為100年，在腐蝕性特別大的環境下運用時，選用內外外表瀝青附層的鋼鋼波紋涵管，可在原運用壽命基礎上提高約20年以上。

鋼波紋涵管這么多，為什么偏偏選擇了衡水浩威新材料有限公司？

鋼波紋涵管優良的經濟特性:銜接方式簡便，可縮短工期；較輕，運輸便利，外加少數的基礎施工，排水管道工程費相對較低如以直徑600mm鋼波紋涵管的施工費與水泥管的施工費的相比較，鋼波紋涵管的施工費用只需要水泥管施工費的90%左右在交通不便利的地方施工時，用人工即可，節省了叉車，吊車等機械設備的費用。

鋼波紋涵管

安裝前作業：檢查鋼制波紋板涵洞底部平整度、水平、標高；核對土建基準，確定涵管的位置、中心軸線、中點。涵管拼裝全部完成，用定扭電動扳手，按預緊力扭矩340N.m±70N.m緊固一切螺栓，依次序，不得遺漏，緊固后底螺栓用紅漆標明。

鋼波紋涵管這么多，為什么偏偏選擇了衡水浩威新材料有限公司？

一切螺栓應在回填之前擰緊，確保波紋的堆疊部分嚴密的嵌套在一起。鋼波紋涵管洛氏硬度洛氏硬度試驗是用必定的載荷將頂角為120度的金剛石圓錐體或直徑為1.588mm的崔火鋼球壓入被測樣外表，依據壓痕的深度確定它的硬度值。洛氏硬度值可從洛氏硬度計刻度盤上直接讀出。

鋼波紋涵管

鋼波紋涵管用洛氏硬度計可以丈量從軟到硬的各種不同資料，這是由于它選用了不同的壓頭和載荷，組成各種不同的洛氏硬度標尺，如HRA、HRB、HRC等。一般生產以HRC（用120度金剛石圓錐體作壓頭，載荷為1500N）用得多，鋼波紋涵管硬度值的標示辦法與布氏硬度相同，硬度值的有用規模為20~70HRC。

為了確保達到螺栓扭矩的要求值，在回填之前隨機抽取結構上縱向接縫上2%的螺栓，用定扭扳手，定預緊力扭矩340N.m±70N.m，進行抽檢試驗。如果有任一試驗值超出了給定的扭矩規模，則應抽檢一切螺栓的5%。如果上述試驗90%以上滿足要求，則認為安裝是合格的；否則應從頭復核，以確定得到的扭矩值是否滿足要求。//hanihanbj.com/